Litecoin mining cgminer guide
Do you have any articles on here that cover building a rig? There is possibly more than one display attatched to a GPU. Probing for an alive pool pool 0 JSON stratum auth failed: Using a as well and the setup on coinotron went successfully.. I also installed the SDK Can you please help me? How long did you wait from starting? GUIMiner takes 2 or so min to start running in my experience.
Cryptocur what do you think of the rig I am planning to build? Funny that you mention it! I have been doing some research the last few days to create an article about mining rigs. It is looking good, the comments are pretty much spot on. However, a bit extra ram and the ssd are nice. Thanks for the great guide. I am using cgminer 2. I have been mining for a week and was wondering about thread concurrency. Now I know, computed it for my card, updated and save cgminer.
I uploaded the zip to mega: Hello, everytime I start cgminer, after a few seconds cgminer causes a problem and maust be closed. At which point I get a popup indicating that cgminer. What am I doing wrong and is my video card supported? This is because miners are also used on infected computers to mine for someone else. I can confirm this, even the one from the official cgminer site shows as a trojan with some av but if you do a little research you can see it is widely used in the litecoin community and all you need to do is add an exception.
FYI Cryptocur I have been promoting this article like mad on reddit. For example, I have a , the bus width is And its start with saying that GPU 0 failure, disabling! Then after a minute, it says that Stratum from pool 0 detected a new block, does this mean that it is working, or not? I entered the command that included all of the information thread concurrency, web address, username, etc. The computer is connected to the internet and the grapics card is working, what do you think could be the issue?
What card are you using, I think it might be the ati sdk, I had a similar problem. You need to install the sdk first then the gpu drivers. What do you think? Furthermore, do i like to have some case coolers. Fixer wil be rewarded. Also open miner s on coinotron. I have one wierd problem. What is problem here????? This will display and retain the error foor you that is causing the crash. So with that said the example using the string in this article would be this,,.
Then when you get it running you can re-edit your config script to remove those args. This will result in a clean stacking of either accepted or rejected shares. Press enter to continue: Is this the case? I try to get my card mining again after installing a new OS: Windows 7 64bit pro. What can I do? Your email address will not be published. You may use these HTML tags and attributes: About Arras WordPress Theme. Cryptocurrencies All the information you need about cryptocurrencies.
Litecoin LTC Mining guide, gpu. Posted April 7, at Posted June 13, at Posted April 8, at Posted April 9, at Posted May 1, at Posted April 9, at 9: Any suggestion number for Geforce M in —thread-concurrency???
Posted April 27, at Posted August 5, at 3: Do you have another pool,better? And can you explain how to set new pool on cgminer. Posted April 9, at 4: Posted June 27, at Posted September 18, at Posted April 10, at 3: First off thanks for the very informative write up, really appreciate it.
Could you please take a look at my screen shot and tell me if it looks ok. Posted April 10, at 7: I am running cgminer I definitely have my worker setup to mine Litecoin on the coinotron end. Posted April 10, at 8: I have now tried the following two combination but I can not get it to accept the commands http: Posted April 10, at 9: Posted April 10, at Posted April 10, at 2: Posted April 11, at 7: Posted April 12, at 6: Posted April 12, at 7: Do not forget to change the file path C: This step is very important and can require quite some time to squeeze out the last hash of your graphics card.
Go to Mining hardware comparison to see what other miners use for their graphics cards. Some times it requires to tweak the settings even more, because every system is different.
Open your batch file again and paste the settings NOTE: Make sure "--scrypt" is included in the parameters list! Right click on your batch file than click "Open" or double click it. You should see something similar to this. Create an account Go to Register if you haven't already created an account. Create your batch file 4. Make your batch file Rename your newly created file to "coinat.
Edit your batch file Right click on "coinat.